How to Replace a Turn Signal Bulb

Turn Signal Bulb Replacement



Safety Tip:
Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or closed toe shoes.



1
Place the ignition key in the on position.
2
Activate your turn signal switch.
6558Photo may not be specific to your vehicle
3
Locate the burned out turn signal bulb.
5727Photo may not be specific to your vehicle
4
Turn the ignition key to the off position.
5
Gain access to the turn signal bulb.
6
Remove the turn signal bulb socket from the lens assembly.
7
Disconnect the turn signal bulb from the socket.
8
Install the new turn signal bulb.
9
Reconnect the socket to the lens assembly.
10
Place the ignition key in the on position. Activate the turn signal switch to verify the repair.

Troubleshoot All types Of Car Problem With proper Solutions

http://carrepairworld.blogspot.com/2015/03/how-to-repair-car-problem.html

 

Know Exactly How Each And Every Part In Your Car Works

http://carrepairworld.blogspot.com/2015/04/how-does-it-work.html

 

Troubleshoot Car OBD Codes.Know Exactly What Each Code Means?

http://carrepairworld.blogspot.com/2015/04/vehicle-obd-ii-codes.html

Comments

Post a Comment

Popular posts from this blog

how to replace Throttle position sensor on 2000 ford expedition

Image
Ford TPS Sensor Replacement Throttle Position Sensor The Throttle Position (TP) sensor is a potentiometer that provides a signal to the PCM that is directly proportional to the throttle plate position. The TP sensor is mounted on the side of the throttle body and is connected to the throttle plate shaft. The TP sensor monitors throttle plate movement and position, and transmits an appropriate electrical signal to the PCM. These signals are used by the PCM to adjust the air/fuel mixture, spark timing and EGR operation according to engine load at idle, part throttle, or full throttle. The TP sensor is not adjustable. The TP sensor receives a 5 volt reference signal and a ground circuit from the PCM. A return signal circuit is connected to a wiper that runs on a resistor internally on the sensor. The further the throttle is opened, the wiper moves along the resistor, at wide open throttle, the wiper essentially creates a loop between the reference signal and the signal return ret...
Read more

Ford TFI-IV System Details And Diagrams

Image
Ford Engine TFI-IV System GENERAL INFORMATION See Figures 1 and 2 Fig. Fig. 1: TFI schematic Fig. Fig. 2: Exploded view of the TFI components The Thick Film Integrated (TFI-IV) ignition system uses a camshaft driven distributor with no centrifugal or vacuum advance. The distributor has a diecast base, incorporating a Hall effect stator assembly. The TFI-IV system module is mounted on the distributor base, it has 6 pins and uses an E-Core ignition coil, named after the shape of the laminations making up the core. The TFI-IV module supplies voltage to the Profile Ignition Pick-up (PIP) sensor, which sends the crankshaft position information to the TFI-IV module. The TFI-IV module then sends this information to the EEC-IV module, which determines the spark timing and sends an electronic signal to the TFI-IV ignition module to turn off the coil and produce a spark to fire the spark plug. The operation of the universal distributor is accomplished through the H...
Read more

Ford F-350 Engine Firing Order

Image
Ford Firing Order With Diagrams See Figures 1, 2, 3 and 4 To avoid confusion, replace spark plug wires one at a time. Fig. Fig. 1: 5.8L engine-nl-> Firing order: 1-3-7-2-6-5-4-8-nl-> Distributor rotation: Counterclockwise Fig. Fig. 2: 4.9L engine-nl-> Firing order: 1-5-3-6-2-4-nl-> Distributor rotation: Clockwise Fig. Fig. 3: 5.0L and 7.5L engines -nl-> Firing order: 1-5-4-2-6-3-7-8-nl-> Distributor rotation: Counterclockwise Fig. Fig. 4: 6.9L and 7.3L Diesel engines-nl-> Injection order: 1-2-7-3-4-5-6-8 This will help. Thanks.
Read more