Engine Warning Light Is On
Today’s cars are controlled by a Powertrain Control Module (PCM), your engine’s computer. If you want to repair or modify your car’s performance, you need a scantool to communicate with the PCM.
Symptoms:
- Check Engine Light on
- Poor Acceleration
- Poor Fuel Economy
- Rough Idle
Probable Cause(s):
- Oxygen Sensors Codes (P0130 to P0167)
- EVAP Code (P0445)
That pesky Check Engine Light, the “Malfunction Indicator Lamp” or “MIL” for short, is on because your vehicle’s computer self diagnosed a fault that could cause your vehicle’s emissions to increase. It doesn’t necessarily mean your vehicle is polluting – or has a serious problem – but it might. So the light is on to let you know something is amiss that needs your attention. Trouble is, you don’t know WHAT the trouble might be. It might be something and could lead to a break-down or cause expensive engine damage, or it might be something minor like a loose gas cap (yes, the on-board diagnostics on 1996 and newer cars can even detect a loose, missing, or leaking gas cap). There’s no way to know what the problem is without talking to your vehicle’s computer. How do you do that? By plugging a diagnostic scantool like AutoTap Express DIY into your vehicle’s diagnostic connector, usually found under the dash near the steering column. This unlocks the secrets that have turned on your Check Engine Light. AutoTap Express DIY will give you the information you need to understand how to diagnose and repair the most common problems in today’s cars, light trucks and SUVs. Whether you perform the repairs yourself, or use the information to better understand what your mechanic is doing, it pays to understand what is going on.
Don’t be a Parts Swapper
The number one mistake made by do-it-yourself mechanics is “parts-swapping”. This expensive practice leads to the replacement of hundreds of dollars of perfectly good parts. At best, a parts-swapper wastes time and money. At its worst, a parts-swapper creates new problems where none existed. Armed with the proper tools and the information from AutoTap Express DIY, you will be prepared to tackle the most common problems found on today’s vehicles, without being a parts-swapper.
The On-Board Diagnostic System - OBDII
When a fault is detected, the Onboard Diagnostics System (OBDII) records a “Diagnostic trouble code” (DTC) in the computer’s memory. The code number corresponds to a particular type of fault. The code might not tell you which component has failed or why, but it will tell you which emission control system or sensor circuit the fault is in, or that your engine is misfiring or running rich (too much fuel) or lean (not enough fuel). When a basic code reader is plugged into your vehicle’s diagnostic connector, it will display any diagnostic trouble codes that are found. The least expensive code readers just give you a number, while the better ones also give you the definition of the code too. You can read codes and get an idea of what’s wrong – and you can even clear the codes from the computer’s memory to turn out the MIL lamp (at least temporarily). But a code by itself isn’t the whole story. Take a code P0171 or P0174. These are codes that indicate your engine is running lean. A lean air/fuel mixture can be caused by any number of things, and may cause symptoms such as a rough idle, hesitation, or stumble when accelerating, hard starting, a loss of power or an emissions failure. Okay, so your engine is running lean. Now what? The next step up the diagnostic ladder is to use AutoTap Express DIY. It can actually provide real diagnostic information. What kind of information are we talking about? Real time sensor data. This is the meat and potatoes of onboard diagnostics and is the data that real technicians rely on to diagnose and repair today’s vehicles.
The diagnostic connector on your vehicle can provide a wealth of information, things like engine speed, engine load, air flow, ignition timing, coolant temperature, inlet air temperature, throttle position, sensor voltages, what’s going on with your engine’s fuel management system, the status of various switches and devices, and more – in fact, up to several hundred different readings are available on some cars depending on the make and model year.
Diagnostic scantools like AutoTap Express DIY:
- Save you money
- Save you time
- Keep your mechanic honest
Knowing what’s causing your problem gives you the option to either fix the problem yourself or to take it to a professional for repairs. If you choose the latter, you won’t be going in blind. You’ll be armed with data that can save diagnostic time and, hopefully, some of your money. In many instances, the Check Engine Light is on because a sensor has failed and needs to be replaced. Some sensors are relatively inexpensive and well within the abilities of a do-it-yourselfer to replace. Some sensors, on the other hand, are quite expensive. A mass airflow sensor might cost a couple hundred dollars or more. So you want to be sure of your diagnosis before you replace such an expensive part – especially since most dealers or parts stores won’t take returns on electronic parts once they’ve been installed.
No comments:
Post a Comment